CamMate ® Controls Manual... Page 30: Table Of Specifications Table of Specifications Dimensions 10.75” W x 10.75” D x 4.75”H Weight Approximately 15 Lbs. AC Power Input 100/240VAC @ 1.0-1.5 Amps Camera Power Supply 15.25V @ 10 Amps Pan Speed 6000 RPM Motor.
Show more
See More
CamMate Manuals. Johnson Controls RW Series Engineering Manual. 2.1 MB - Johnson Controls, Chiller. TJERNLUND XCHANGER X2R Installation Instructions Manual. 352.9 KB - TJERNLUND, Ventilation Hood. ClosetMaid SuiteSymphony 1936340 Installation Tips. 726.6 KB - …
Show more
See More
CamMate Manuals. Vanguard VGFRG-2124-2125BK Installation Instruction. 774.8 KB - Vanguard, Automobile Accessories. Weston 2VL1 Manual. 6.7 MB - Weston, Control Unit. Panasonic CF-18 Series Supplementary Instructions. 654.7 KB - Panasonic, Desktop. Trinamic PD-1160 Getting Started.
Show more
See More
CamMate Manuals. Clas Ohlson BL5606 Instruction Manual. 358.2 KB - Clas Ohlson, Speakers. Carrier 38YKC Series Manual To Operating & Maintenance. 137 KB - Carrier, Heat Pump. BOMANN KM 363 CB Instruction Manual. 1.4 MB - BOMANN, Food Processor. Waeco PerfectView CAM26W Installation And Operating Instructions Manual.
Show more
See More
CamMate Manuals. Birch DSP-850 Series User Manual. 572.1 KB - Birch, Monitor. SOMFY J4 io Installer\'s Manual. 1 MB - SOMFY, DC Drives. EUFY HomeVac H11 Owner\'s Manual. 4.6 MB - EUFY, Vacuum Cleaner. Polycom VVX 500 Series User Manual. 1.7 MB - …
Show more
See More
CamMate Operations Manual CamMate Systems Phone: (480) 813-9500 Fax: (480) 813-9292 425 E. Comstock Chandler, AZ 85225 USA www.CamMate.com [email protected] ATTENTION Verify clean AC power (100-240vac) before connecting CamMate Electronics Control Box.
Show more
See More
CamMate is Celebrating over 25 Years of Offering Top Quality Products, with the "Original" Octagon Arm and the First T-Bolt Locking Design . Since 1987, CamMate Systems has been delivering the highest quality cranes for the film and video industry. Producers, Directors, and Directors of Photography all over the world have discovered the quality and versatility that our equipment has to offer.
Show more
See More
Please Note: I am a beginning machinist and I do not pretend to know everything. Please always operate machinery in a safe manner and if you don't know, fin...
Show more
See More
How to SETUP a JIB CRANE / ZCAM + CamMate Traveller. In this video we test the CamMate Traveller Jib Crane and the ZCam E2-S6 for the first time. How to setu...
Show more
See More
Documentation – Arm Developer
Show more
See More
JIBOWNER.com - Tampa Bay Camera Crane Rentals - CamMate Jib Services for Florida Television & Film Production. CamMate Sizes. The CamMate takes between 20-45 minutes to setup depending on the size requested. 1 Span. 2 Spans. 4 Spans. 3 Spans. 5 Spans. 6 Spans. 13' 5" 18' 9" 24' 1" 29' 5" 34' 9" 40' 1" THE SET UP. LOCATION. Our Jib is located in ...
Show more
See More
The world-famous CamMate Travel Series is a more economical version that consists of four-foot sections packed in durable hard cases for frequent location tr...
Show more
See More
The CamMate Systems Telescopic Camera Crane provides booming motion. Starting at 10 feet and extending out to a 19 foot reach.
Show more
See More
ROBOTIC / MANUAL CAMERA Operate robotic, manual and Jib cameras as assigned for live or taped productions. Provide network level shot composition and execution at all times. Perform daily fax check of all camera equipment to ensure all operational functions are performing as expected.
Show more
See More
Manual control is also possible from the camera itself, including rotation of the extra booms. I believe the geometry of the mechanical connections is unique, employing three vertical axes 24 , 74...
Show more
See More
A: Stype kit was designed to be used with industry standard camera crane – the Stanton Jimmy jib USA, CamMate crane or Supertechno telescopic jib. Every Stype kit component is carefully thought through so the whole system works like a plug and play device. This means it takes 1 hour for the first installation and once the components are in ...
Show more
See More
Exercise 1: Assigning a Machine Definition In this exercise, you open an existing part , assign a machine definition to the part, and save it under a new file name. 1 Start Mastercam using your preferred method: Double-click Mastercam’s desktop icon. Or
There are normally three or four steps in any CAD/CAM process: 1. Create your part/design in either a CAD package or an 'art' application like Corel Draw. 2. Open/import the drawing as a DXF, HPGL or Excellon file into the CAM program and set up your tooling sizes and cutting operations.
While SheetCam does not directly control the machine (except in special circumstances) the post processor code generated by SheetCam is used by other software that in turn controls the machine operation.
Contact your local Mastercam Re seller for more information. You must install Adobe Flash Player to display tutorial videos. You can download Adobe Flash Player from www.adobe.com. All Mastercam tutorials require you to configure Mastercam to work in a default metric or English configuration.