Dec 05, 2017 . Fast-Stat Installation Instructions. The Simple thermostat requires a C-wire connection for continuous power in order to maintain Wi-Fi connectivity. Some houses have a C-wire already at the thermostat, but if not you will need to use either a Fast-Stat 1000, or a Fast-Stat Common Maker, depending on your household wiring.
Show more
See More
Fast-Stat1000 : Model 3000: 3000-Fast-Stat ... Model 5000: 5000-Fast-Stat : Model 7000: Fast-Stat7000 : Model 9000: Fast-Stat9000 : Back. Sigler. Website . …
Show more
See More
Mar 02, 2017 . Visit http://www.smarthvacproducts.com/product/Fast-Stat-common-maker to learn more.The Fast-Stat Common Maker Thermostat Wire Extender eliminates the need t...
Show more
See More
Model 3000 - Fast-Stat. Add or Upgrade HVAC Equipment Without Installing New Cables. Model 3000. Installation Instructions.
Show more
See More
In this video I explain the relationship between the gas and the clutch and how you can use them to make a manual car accelerate quickly from a standstill. I...
Show more
See More
Plotting the clipping results. Using the FASTX-toolkit from the command line: $ fastq_to_fasta -v -n -i BC54.fq -o BC54.fa Input: 100000 reads. Output: 100000 reads. $ fastx_clipper -v -i BC54.fa -a CTGTAGGCACCATCAATTCGTA -o BC54.clipped.fa Clipping Adapter: CTGTAGGCACCATCAATTCGTA Min. Length: 15 Input: 100000 reads.
Show more
See More
Visit http://www.smarthvacproducts.com/product/Fast-Stat to learn more about Fast-Stat.Fast-Stat wiring extenders allow installers to use existing thermostat...
Show more
See More
The Common Maker adds a common C connection to a thermostat cable with 2 or more wires. A common connection allows the thermostat to operate without batteries or power stealing circuits. Compatible with all major name brand Wi-Fi thermostats and HVAC equipment, including furnaces, air handlers, zone valves, zone controllers, millivolt systems ...
Show more
See More
Article: Fast-Stat Installation. Article: Heat Only Installation (Option #4, #5) Installing ecobee with Heat Pump & Dual Fuel Systems. ecobee thermostats are compatible with heat pump and dual fuel setups, provided your system uses a single O/B wire. Your system won't be compatible if it …
Show more
See More
Fast-start failover quickly and reliably fails over the target standby database to the primary database role, without requiring you to perform any manual steps to invoke the failover. Fast-start failover can be used only in a broker configuration and can be configured only through DGMGRL or Cloud Control.
Show more
See More
The Fast-Stat Model 5000 adds additional HVAC control wiring between a thermostat and indoor unit. It provides R, C, G, Y, W1 & W2 connections over a 2-wire thermostat cable. Additional thermostat cable wires can be used for other functions. Before Installing This Product
Some houses have a C-wire already at the thermostat, but if not you will need to use either a Fast-Stat 1000, or a Fast-Stat Common Maker, depending on your household wiring. Common configurations found in houses that are covered in this guide are:
Insert the receiver module’s purple wire and your original Y-wire into a wire nut and twist until secure. Once all wires are secured, close the control panel door, and turn the power to the system back on. You may now continue with your installation process. Shut off the power to your thermostat and remove it from the wall.
The receiver gets mounted next to your A/C control panel, and the sender goes behind your thermostat, tucked into the wall. To perform the installation you will need a small phillips screwdriver, a set of wire strippers/cutters, and the supplied wire nuts.
Insert the receiver module’s purple wire and your original Y-wire into a wire nut and twist until secure. Once all wires are secured, close the control panel door, and turn the power to the system back on. You may now continue with your installation process. Shut off the power to your thermostat and remove it from the wall.
Connect the receiver module’s yellow wire to the Y terminal. Connect the receiver module’s red wire to the R terminal. Connect the receiver module’s green wire to the G terminal. Connect the receiver module’s black wire to the C terminal. Insert the receiver module’s purple wire and your original Y-wire into a wire nut and twist until secure.
The receiver gets mounted next to your A/C control panel, and the sender goes behind your thermostat, tucked into the wall. To perform the installation you will need a small phillips screwdriver, a set of wire strippers/cutters, and the supplied wire nuts.
Both the Fast-Stat 1000 and the Fast-Stat Common Maker come with a receiver (top) and a sender (bottom). The receiver gets mounted next to your A/C control panel, and the sender goes behind your thermostat, tucked into the wall.