Fleck 5600 Sxt Manual

Listing Results Fleck 5600 Sxt Manual

About 19 results and 8 answers.

Fleck 5600 SXT Metered Water Softener 5600SXT

The 5600 Fleck valve is the most popular water softener control valve on the planet and offers a rigid Noryl valve body with low power consumption and a precision piston-seal-spacer assembly. It was updated from the old mechanical-meter to the 21 st Century SXT electronics.

Show more

See More

Fleck Service Manuals Nelsen Corporation

5600SXT Down Flow Service Manual Size: 2.1 mb. 5600SXT Up Flow Service Manual Size: 1.8 mb. 5800SXT Service Manual Size: 2.5 mb

Show more

See More

Fleck 5600 SXT: How to program your water softener - YouTube

This is a step-by-step tutorial on how to enter the programming for your Fleck 5600 SXT water softener. We will walk you through each setting, explaining wha...

Show more

See More

Frequently Asked Questions

  • What do you need for a Fleck 5600sxt downflow valve?

    FLECK 5600SXT Downflow Service Manual INSTALLATION Water Pressure A minimum of 20 pounds (1.4 bar) of water pressure is required for regeneration valve to operate effectively. Electrical Facilities An uninterrupted alternating current (A/C) supply is required.

  • Who is the manufacturer of the Fleck 5600?

    Manufacturer:Pentair International LLC Avenue de Sevelin 18 1004 Lausanne Switzerland Product: Fleck 5600 SXT Installer manual Fleck 5600 SXT - Generalities 8 / 104 Ref. MKT-IM-013 / E - 23.09.2020 1.4Intended use The device is intended for domestic applications use only and it is purpose-built for water treatment.

  • How to install a Fleck 5600 softener tank?

    Fleck 5600-SXT Softener Installation & Startup Guide Page 7 www.cleanwaterstore.com Rev 072514 Installation Instructions 1. Unscrew by hand the entire Fleck 5600-SXT control valve from top of tank if it was shipped screwed on. Place distributor tube in tank if not already inside tank. If not already done, make sure blue cap is

  • What should water pressure be for Fleck 5800 SXT?

    2 • FLECK 5800 SXT Upflow/Downflow INSTALLATION Water Pressure A minimum of 20 psi (1.4 bar) of water pressure is required for the regeneration valve to operate effectively. Electrical Facilities An uninterrupted alternating current (120 VAC) supply is required. The control uses a transformer to supply 12 VDC.

  • What do you need for a Fleck 5600sxt downflow valve?

    FLECK 5600SXT Downflow Service Manual INSTALLATION Water Pressure A minimum of 20 pounds (1.4 bar) of water pressure is required for regeneration valve to operate effectively. Electrical Facilities An uninterrupted alternating current (A/C) supply is required.

  • Is there a warranty on the Fleck 5600 SXT?

    Installer manual Fleck 5600 SXT - Generalities 10 / 104 Ref. MKT-IM-013 / E - 23.09.2020 1.9Limitation of liability Pentair Quality System EMEA products benefit, under specific conditions, from a manufacturer warranty that may be invoked by Pentair’s direct customers.

  • How to install a Fleck 5600 softener tank?

    Fleck 5600-SXT Softener Installation & Startup Guide Page 7 www.cleanwaterstore.com Rev 072514 Installation Instructions 1. Unscrew by hand the entire Fleck 5600-SXT control valve from top of tank if it was shipped screwed on. Place distributor tube in tank if not already inside tank. If not already done, make sure blue cap is

  • How does the brine draw in Fleck 5600sxt work?

    During the brine draw (BD) stage of the regeneration of the Fleck 5600SXT this drain line flow is passed over the injector (an inside component in the control valve) to create suction to draw the brine solution out of the brine tank.

Have feedback?

If you have any questions, please do not hesitate to ask us.