JLG Boom Lift Error Codes - Forklift Trucks Manual PDF ...
Show more
See More
JLG Boom Lift Fault Codes list 116. Fault Message: ECT higher than expected stage 1 Description: Engine Coolant Temperature reading or estimate greater than the stage 1 limit when operating at a speed greater than defined in the diagnostic calibration.
Show more
See More
Nov 23, 2016 . Popular JLG Troubleshooting Codes. Error Code: 212; Fault Message: Faulty Keyswitch. Description: Both platform and ground modes are selected simultaneously. Check: Key switch function, Check wiring to key switch function. Error Code: 221; Fault Message: Horn Permanently Selected. Description: The horn switch was closed during power-up in platform mode.
Show more
See More
JLG has received reports of DEF-related engine fault codes on JLG® and SkyTrak® telehandlers equipped with Cummins Tier 4F engines. Ensure the DEF (diesel exhaust fluid) solution is the correct specification. Cummins recommends using only DEF solutions that maintain 32.5% (+ or -1.5%) of urea content by weight.
Show more
See More
Dec 02, 2016 . Fault Message: Microprocessor failure RTI 3. Description: Internal microprocessor error. DTC: 1615. Fault Message: Microprocessor failure A/D. Description: Internal microprocessor error. DTC: 1616. Fault Message: Microprocessor failure Interrupt. Description: Internal microprocessor error. DTC: 1625. Fault Message: CAN J1939 shutdown request
Show more
See More
Search: JLG Fault Code List. If you are search for JLG Fault Code List, simply check out our text below :
Show more
See More
Jul 11, 2012 . . JLG lift trouble codes flashes 9 times - Answered by a verified Mechanic We use cookies to give you the best possible experience on our website. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them.
Show more
See More
JLG is a leading manufacturer of lift equipment, including aerial lifts, boom lifts, scissor lifts, telehandlers and low-level access lifts. By continuing to browse this website, you are agreeing to our use of cookies. For more information about our use of cookies, please visit our Terms page.
Show more
See More
JLG TOUCAN VM 3242E, VM 2642E Service Repair Manual (P/N: 31210043) JLG TOUCAN 8E / 20E, TOUCAN 10E / 26E Service Repair Manual. JLG Vertical Mast AM-19,AM-24,AM-30,AM-36 AC & DC Models Service Repair + Parts Manual. JLG CM2033,CM2046, CM2033,CM2546, CM2558 Models Service Repair Workshop + Parts Manual.
Show more
See More
Dec 12, 2013 . JLG 2033E3: Code 25. Ser# 0200075820. It periodically times out prematurely, once either lift or travel is selected on the plate form display and the joystick is activated in either direction ( time interval of 2 to 20 seconds ) The machine has to be reset with the emergency shut off. Batteries and voltages are good.
Show more
See More
JLG Boom Lift Fault Codes list 116 Fault Message: ECT higher than expected stage 1 Description: Engine Coolant Temperature reading or estimate greater than the stage 1 limit when operating at a speed greater than defined in the diagnostic calibration.
Error Code: 212; Fault Message: Faulty Keyswitch. Description: Both platform and ground modes are selected simultaneously. Check: Key switch function, Check wiring to key switch function. Error Code: 221; Fault Message: Horn Permanently Selected. Description: The horn switch was closed during power-up in platform mode.
Description: Electrical noise or irregular crank pattern detected causing x number of crank resynchronization events Corrective Action: Illuminate MIL and/or sound audible warning or illuminate secondary warning lamp and disable fueling correction for remainder of key cycle.
Popular JLG Scissor Lifts: 1 JLG 1930ES. 2 JLG 2030ES. 3 JLG 2032ES. 4 JLG 2630ES. 5 JLG 2632ES. 6 JLG 2646ES. 7 JLG 3246ES JLG troubleshooting diagnostic codes: If the number starts with….. it’s a 2-1 – Power Up Problem 2-2 – Platform Controls 2-3 – Ground ...
JLG Scissor Lifts Fault Codes 212. Fault Message: Faulty Keyswitch Description: Both platform and ground modes are selected simultaneously. Check: Key switch function, Check wiring to key switch function. 221. Fault Message: Horn Permanently Selected Description: The horn switch was closed during power-up in platform mode.
Description: The horn switch was closed during power-up in platform mode. Check: Check if the horn is damaged, obstructed or jammed. Description: The joystick signal is outside the acceptable range of 0.5V – 4.5V. Check: Center joystick and check to see if a power cycle will clear DTC.
Description: Electrical noise or irregular crank pattern detected causing x number of crank resynchronization events Corrective Action: Illuminate MIL and/or sound audible warning or illuminate secondary warning lamp and disable fueling correction for remainder of key cycle.
I have a JLG 2630ES Scissor lift, won't lift or drive from I have a JLG 2630ES Scissor lift, won't lift or drive from control box. Yellow fault code is flashing 2 times …