To eliminate unnecessary service calls, the KE2 Temp + Defrost alerts the user when it is coming out of a defrost cycle using the onboard display. The display alternates between dEF and the actual temperature measured by the air sensor. This continues until the temperature has reached setpoint, or for the amount of time set by dFt (Defrost Time)
Show more
See More
KE2 Therm Solutions, Inc 12 Chamber Drive, Washington, MO 63090 636.266.0140 fax 888.366.6769. information@KE2therm.com
Show more
See More
User Manuals, Guides and Specifications for your KE2 Therm Solutions KE2 LDA Network Hardware. Database contains 1 KE2 Therm Solutions KE2 LDA Manuals (available for free online viewing or downloading in PDF): Overview, installation, and setup instructions . KE2 Therm Solutions KE2 LDA Overview, installation, and setup instructions (16 pages)
Show more
See More
KE2 Therm Solutions Evaporator Efficiency Installation Instructions Manual Download for Free KE2 Therm Solutions Evaporator Efficiency Controller …
Show more
See More
KE2 therm solutions seeks to save energy, preserve the. Motor starters with short circuit and thermal. KE2 low temp + defrost kit. Welcome to young supply's online. Replaces thermostat and time clock; . KE2 switch part of the refrigeration network.
Show more
See More
KE2 Therm offers general guidance for sensor locations based on the coil construction. Figure 3 shows the recommended locations for the coil sensor for each evaporator type. When installing on draw through models, the sensor should be located behind the coil in the lower corner nearest the suction header.
Show more
See More
KE2 Therm Solutions, Inc. ›. 21804. An FCC ID is the product ID assigned by the FCC to identify wireless products in the market. The FCC chooses 3 or 5 character "Grantee" codes to identify the business that created the product. For example, the grantee code for FCC ID: 2AOPR-21804 is 2AOPR. The remaining characters of the FCC ID, -21804, are often …
Show more
See More
Contact KE2 Therm. After the wire has been successfully routed, it may be connected to the pluggable terminal on the controller. Coil Temperature Sensor - As a critical input to the control- ler, it is essential the sensor is located at the coldest point on the evaporator coil for optimal operation.The coil sensor is an
If viewing the temperature outside the walk-in or refrigerated room is desirable, the KE2 Evap may be used as a digital thermo- stat. The controller is then installed near the door of the space KE2 Evaporator E ciency TM therm solutions ENTER BA CK
The KE2 Evaporator Efficiency (KE2 Evap) is an electronically op-erated evaporator controller engineered to save energy in re-frigeration systems through precise control of superheat, space temperature, fan cycling, reducing compressor runtime, and.
Installation N.1.1 July 2011 Page 2 Introduction The KE2 Evaporator Efficiency (KE2 Evap) is an electronically op - erated evaporator controller engineered to save energy in re- frigeration systems through precise control of superheat, space temperature, fan cycling, reducing compressor runtime, and
fans, liquid line solenoid, and the controller. Foam insulation if running wires outside the space. Page 1 KE2 Local Area Dashboard and compressor) Alarms (KE2 LDA). See page 14 for additional details. Additional Inputs - e.g. Door switch and additional sensors © Copyright 2017 KE2 Therm Solutions, Inc., Washington, Missouri 63090...
Page 4 Note: KE2 Therm offers pre-made wiring harnesses to simplify installation. Each harness contains the proper color coded and sized wires, with flag terminals already installed. Refer to the ac- cessories listed on page 1. © Copyright 2017 KE2 Therm Solutions, Inc., Washington, Missouri 63090...
If crossing a high voltage line is necessary, the sensor wiring should be run at right angles to prevent noise. © Copyright 2017 KE2 Therm Solutions, Inc., Washington, Missouri 63090... The KE2 Low Temp includes RS-485 Modbus communications, and can now be accessed remotely using the KE2 Local Area Dashboard and Alarms (KE2 LDA).
The KE2 Low Temp includes RS-485 Modbus communications, and can now be accessed remotely using the KE2 Local Area Dashboard and Alarms (KE2 LDA). See page 14 for further details. © Copyright 2017 KE2 Therm Solutions, Inc., Washington, Missouri 63090...