Using the BIOS RAID Configuration Utility
Show more
See More
Choose RAID Level, for example :RAID0(Stripe)，as below picture mark red 2. Select the disks that you want to create and set to [X]，as below picture mark red 3. 12. Set RAID capacity and click [Create Volume] to create RAID. Below is set the max RAID capacity ※Note：Be cautious when create or deleting a RAID set. You will lose all data on the hard disk drives when you delete a RAID set
Show more
See More
1. Start the BIOS RAID Configuration utility. See Running the BIOS RAID Configuration Utility. 2. Select the HBA you want, then press Enter. 3. Select Disk Utilities. 4. Select the disk drive you want, then press Enter. 5. Select Identify Drive, then press Enter. 6. When you have finished locating the disk drive, press any key to stop the blinking.
Show more
See More
Show more
See More
How to Access RAID BIOS in UEFI mode. When these systems are configured in UEFI BIOS mode, the RAID setup is accessed from the F12 pre-boot menu. Press F12 on power up while at the Dell logo splash screen. Then, select " Device Configuration " from the …
Show more
See More
For RAID 0, select RAID 0 (Stripe) and press ENTER or for RAID 1 select RAID 1 (Mirror) and press ENTER. Select the two drives that will constitute the RAID configuration and press ENTER. For RAID 0, change the stripe size and press ENTER. For RAID 1, skip this step.
Show more
See More
To enable RAID, use one of the following methods, depending on your board model. Go to Configuration > SATA Drives, set Chipset SATA Mode to RAID. Go to Advanced > Drive Configuration, set Configure SATA As to RAID. Go to Advanced > Drive Configuration, set Drive Mode to Enhanced and set the RAID option to Enabled. Press F10 to save and exit.
Show more
See More
Some of the screen shots and operations could be different from the software versions. ASUS provides the above information for reference only. If you have any questions about the content, please contact the above product vendor directly. Please note that ASUS is not responsible for the content or service provided by the above product vendor.
Show more
See More
Select [SETTINGS] → [Advanced] → select [Intel (R) Rapid Storage Technology]. Select [Create RAID Volume] Select [RAID Level] Select the RAID mode according to your need. Here we take the RAID0 as an example, select [RAID 0 (Stripe)]. RAID 0: Minimum two or more disks with the same amount of channels, protocol and capacity.
Show more
See More
Nov 05, 2010 . A basic guide on how to set up a RAID array using your motherboard chipset.
Show more
See More
Feb 16, 2012 . RAID-1 provides the best performance and some fault-tolerance in a multi-user system, although for a single user it's unlikely to see as much benefit. Again drives are typically added in multiples of two. RAID-2 (non-consumer): This type uses striping across disks with some disks storing error checking and correcting (ECC) information.
Show more
See More
Jun 17, 2019 . Jun 17, 2019 . From the chipset screen, you should navigate to SATA Mode and select RAID instead of AHCI. You have now successfully initialized Raid on your motherboard; simply hit Save & Exit. The computer will restart at this point and will attempt to …
Show more
See More
Feb 14, 2018 . I don't know if it is the right place for my problem here but I can't handle it myself.I bought an AsRock A320M motherboard last year and today I wanted to create a RAID setup.I followed the instructions from the motherboard's website but my pc restarts.I press CTRL+R, it enters in the "ROM UTILITY.....and so on" but when I have to press again CTRL+R it just restarts.I would be very grateful ...
Show more
See More
1. Start the BIOS RAID Configuration utility. See To Start the BIOS RAID Configuration Utility. 2. If you have more than one HBA, select the HBA that you want to manage and press Enter. 3. Select Array Configuration Utility and press Enter. 4.
If your motherboard supports Intel®Rapid Storage Technology, you can create RAID 0, RAID 1, RAID 5 or RAID 10 configurations. If you want to install a Windows®operating system to a hard disk drive included in a RAID set, you have to create a RAID driver disk and load the RAID driver during OS installation.
GIGABYTE motherboards provide you with the EZ RAID feature, allowing you to quickly configure a RAID array with simplified steps. Step 1: After restarting the computer, enter the BIOS Setup and go to Peripherals. Press <Enter> on the EZ RAID item. Select the type of hard drives you use for RAID in the Type tab and then press <Enter>.
From the configuration utility main menu, select Create RAID Volume and press <Enter>. The following screen appears: In the Name field, specify a name for the RAID 0 set and press the <Tab> key or <Enter> to go to the next field. (To select the previous menu, press <Esc>.)
The SATA Mode BIOS feature is similar to the SATA Operation Mode BIOS feature, but with different options available. It controls the SATA controller’s operating mode. There are three available modes – IDE, SATA or AHCI and RAID. When set to SATA or AHCI, the SATA controller enables its AHCI functionality.