Documents — NavSpark. Information particular to a specific product can be found on their product page in NavSpark Shop . Common information for NavSpark products are provided here. NavSpark, NavSpark-BD, NavSpark-GL, NavSpark-mini User Guide (.pdf, ver 0.9) NavSpark Programmer Guide (.pdf, version 0.4) GNSS Viewer User Guide (.pdf 20151224)
NavSpark is an Arduino-IDE programmable GPS/GNSS board. Not familiar with Arduino? Please visit Getting Started with Arduino.To start playing with NavSpark, take a quick look at NavSpark User Guide and then work on Tutorial 1.After that, pick any other tutorials that may interest you.
Windows. 1. Get a NavSpark board and a micro USB cable. In this tutorial, we assume you're using a NavSpark, NavSpark-GL, or NavSpark-BD. You need to solder you NavSpark board in order to work on a breadboard. View fullsize. If you own a NavSpark-mini, the following example is not compatible with NavSpark-mini.
Aug 14, 2015 . The user's manual has warnings that the one ADC input on NavSpark is untested and may not work at all. However there is an example program provided to test it. If you use the example program as-is, you will get poor quality output because it sets a high ADC clock (20 MHz). If you cut that down to 2 MHz, the output looks much better.
Along with latest Windows and Linux Board Manager support update, the NavSpark I2C library has been improved to allow easier adoption of other vendor's example code when using their break board. Using Adafruit's 10DOF break board and BNO055 break board, below list modification guidelines needed to make them work with NavSpark: 1.
Reviews: 1
Published: May 18, 2014
Jan 20, 2016 . NavSpark mini (Left) and USB to TTL board (Right) Connected to Breadboard – Click to Enlarge. I also connected the GPS antenna from LinkIt ONE development kit to the uFL connector on NavSpark mini, as well as a micro USB to USB cable to my computer. If you don’t have such antenna, you’ll need to add the $9 GPS/GLONASS antenna on NavSpark website …
Navigation and positioning. NaviPac provides positioning and navigation features for surface and/or subsea vehicles. It comes in four variants: NaviPac Pro, the variant you see here; NaviPac Single User, which offers all the features of NaviPac Pro, limited to a single network/remote client and a single subsea object; NaviPac Lite, which is tailored to vessel-based surveys with a …
NavSpark pinout from the User Manual These pins have to be connected to a Raspberry Pi 2’s GPIO pins. Raspberry Pi 2 pinout diagram Based on the pinout above, and some digging around, the connections I needed to make between the Pi (left) and NavSpark (right) were: 5V ↔ BATTERY Ground ↔ GND GPIO15 (UART0_RX) ↔ TXD1 GPIO8 ↔ P1PPS (GPO3)
Jan 04, 2016 . The board is compatible with Arduino 1.6.5 for Linux and Windows, and functionally compatible with NavSpark, and in theory all you have to do is to add the Board Manager URL for NavSpark in the IDE, install the compiler, and follow the instructions in the tutorial.That said tutorial however mentions that “If you own a NavSpark-mini, the following …
Jan 26, 2014 . The currently remaining Flash/RAM space for user applications on NavSpark, NavSpark-GL, NavSpark-BD is roughly 490/45, 420/20, 440/10 Kbytes. NavSpark-RAW is not programmable. NavSpark (GPS-only) is generally a good choice with a larger programmable space (490KByte Flash, 45KByte RAM).
Nov 26, 2015 . The NavSpark module has a 1PPS pin (GPO3 below), and the only other pin I’ll really need is a serial pin to receive the NMEA stream of the satellite lock data (TXD1 below). NavSpark pinout from the User Manual
Show more
Although the Emlid GNSS had superior localization performance, as its percentage of data in fixed solution status was 94.0% compared to 71.5% for the NavSpark GNSS, both were deemed promising for use on experimental field robots. KW - Field robotics. KW - GPS data. KW - Precision agriculture. KW - Single-frequency
Show more
I also connected the GPS antenna from LinkIt ONE development kit to the uFL connector on NavSpark mini, as well as a micro USB to USB cable to my computer. If you don’t have such antenna, you’ll need to add the $9 GPS/GLONASS antenna on NavSpark website to your order.
NaviPac Helmsman’s Display 4 (based on the same core as NaviModel) supports display of vehicle data (main vessel, ROV, ROTV, remotes etc) based on the NaviPac data feed. The data can be shown graphically in multiple map views. All variants of NaviPac supports integration with AIS receivers.
NAVTOR NavTracker User Guide This guide is based on NavTracker 7.12.0.0 NAVTOR AS +47 51 49 22 00 pg. 2 TABLE OF CONTENTS
NaviPac supports a series of runline and waypoint formats including our own RLX/WPT format, ad generic ASCII readers. You can also draw lines and points directly in the Map View. You can inherit multiple lines based on the base line defined, such as parallel or cross lines to get an optimal route plan.
The favourite list in NavTracker Desktop and the App version are synchronized with each other. Add to favourites - Select the relevant vessel from the fleet list, then right click and select [Add To Favourites]. - Or double click on the relevant vessel from the fleet list, then tap the star icon next the refresh icon.
1. Open NavTracker by double-clicking the desktop icon a. Minimumconnection requirement for accessing NavTracker (low-bandwidth mode): Server Address Port Number Fixed IP https://navserver2.navtor.com 443 23.100.54.138 https://navstorage.navtor.com 443 23.100.54.139 2.
Server Address (FQDN) Port Number Fixed IP https://navserver2.navtor.com 443 23.100.54.138 https://navstorage.navtor.com 443 23.100.54.139 Note that our SSL certificate requires the above hosts to be accessed via the FQDN (ref. table above).