North Star pressure washer troubleshooting: not working ...
Show more
See More
Mar 19, 2018 . North Star 157596 pressure washer troubleshooting. Check the mains voltage (+/- 5% tolerance). Check the phases in the plug are connected well. Replace the valve or the gasket and check the pressure valve body wear. Check the water supply flow and the relative pressure (2+10)
Show more
See More
Aug 26, 2010 . What's wrong with it? We are about to find out. Check back soon for update :)....
Show more
See More
To determine if your washer is getting the proper amount of air, check for white smoke at burner ignition. A slight puff of white smoke is normal. Excessive white smoke is not normal and indicates there is too much air at combustion. Not enough air causes black smoke.
Show more
See More
Feb 06, 2011 . 1. Flow switch. Test by using alligator wire jumper clips from inside the control box to short across the wire terminals and see if this solves your problem. Flow switch is a cleanable item. See page 16 of heater owners manual. 2.
Show more
See More
Turn off machine (but not water supply) and release pressure by squeezing trigger gun. Obstructed nozzle, water inlet filter or gun/spray wand. Use needle to clear nozzle, fresh water to flush water inlet and vinegar to clear any deposits in gun/wand. 4.
Show more
See More
Sep 14, 2010 . Burner started throwing dark smoke and quit heating up the water...I checked the fuel filters (outside and inside the pump), checked fuel flow after the pump...
Show more
See More
Aug 05, 2019 . Old fuel can wreak havoc on all burner parts. Check Fuel Filter. Dirty or old fuel will ruin the filter quickly, leading to more issues. A visual check on the fuel filter is never a bad idea. Air Supply. Before you fire up your hot water pressure washer, make sure it has some room to breathe.
Show more
See More
Jan 27, 2014 . An instructional for our NorthStar Gas Powered Wet Steam & Hot Water Pressure Washer.For more information visit Northern Tool + Equipment:http://www.northern...
Show more
See More
The NorthStar® ProShot Belt Drive Hot Water Pressure Washer Trailer is the ultimate commercial-grade cleaning solution for professionals — exclusive ProShot technologies, up to 35% increased fuel efficiency and accurate temperature regulation handle the toughest jobs, plus save you time and money.
Show more
See More
Product Summary. This NorthStar® 12 Volt Burner fits the NorthStar 3000 PSI Wet Steam & Hot Water Pressure Washer, Item# 157310, NorthStar 4000 PSI Hot Water Pressure Washer Skid, Item# 157594, both sold separately.
Show more
See More
Oct 27, 2014 . My heater is not firing. It is a northstar diesle heater. I have done the following. I checked the flow switch, working. I checked the transformer and am getting good spark accross the springs. I checked the fuel pump and fan, pumping fine. Emptied the fuel filter and checked for water.
Show more
See More
Pressure Washer Hose", "longDescription": "This NorthStar 25ft. 5/16in. Pressure Washer Hose fits the NorthStar Gas Cold Water Pressure Washer, Item# 1575440, and NorthStar Electric Cold Water Pressure Washers, Item#s 15743011 and 1573021, all sold separately."
Show more
See More
BEAST NorthStar Soft Wash System Training Video: How to Setup to Soft Wash Roof, Siding, Fences + More Instructional for NorthStar Gas Powered Wet Steam \u0026 Hot Water Pressure Washer (SKU #157310) NorthStar 2-Gun Hot Water Pressure Washer Trailer - …
Show more
See More
This 8.700-944.0 1.75 x 80B Diesel Oil Burner Fuel Nozzle has a SOLID CONE SPRAY pattern for use with diesel-fired heating equipment including pressure washers and waste oil heaters. Delavan Type B oil burner fuel spray tip nozzles are used on burners with a solid cone air pattern. With Type B nozzles the diesel oil … Burner Nozzle, 1.75 x 80B Read More »
Show more
See More
A REPAIR KIT IS AVAILABLE FOR THIS UNLOADER USE KIT GPYKITU2121. IF YOU ARE NOT SURE WHICH UNLODER YOU HAVE, CALL US. THIS UNLOADER WAS USED BY NORTHSTAR WITH BOTH SINGLE AND TWO GUN PRESSURE WASHERS. CALL US IF YOU WANT A NEW UNLOADER. THE PART NUMBER CHANGES BY DIFFERENT ITEM NUMBERS.
Show more
See More
Check the water supply flow and the relative pressure (2+10) Prime the pump without the lance Check the valves, clean and reassemble Clean the filter Clean the filter Replace the electrodes Replace the pressure switch Fill engine with the adequate amount of oil. Choke engine to start. Add gas to engine, make sure fuel shutoff valve is open.
Like it or not, the day may come where your hot water pressure washer burner, isn't quite working well. We see this problem fairly often. Luckily, simple regular maintenance can help prevent more significant issues. Also, keeps your pressure washer running efficiently to prevent downtime.
Make sure you have clean and fresh fuel. Old fuel can wreak havoc on all burner parts. Dirty or old fuel will ruin the filter quickly, leading to more issues. A visual check on the fuel filter is never a bad idea. Before you fire up your hot water pressure washer, make sure it has some room to breathe.
Don’t make this mistake – always check for kinks. Release air from system: Always connect the garden hose to the power washer first. Then turn the water tap on and pull the trigger gun to release water from the system at the garden hose water pressure before starting the engine or motor.
Summary Table of Troubleshooting Tips: 1. Low pressure None or incorrect nozzle Ensure correct nozzle being used 2. No pressure 2. No pressure Damaged pump inlet valves/manifold Disassemble pump and replace/clean compo ... 3. Pulsing pressure (high then low) 29 more rows ...
If there was no unloader valve then pressure would build inside the system (when not in use) so when you did pull the trigger it would stall the engine or explode a weak link part – probably the pressure hose o-ring. Check out where the unloader is located on 3 different pressure washer pumps:
The surface cleaner’s sealant is clogging up the nozzles. You may have to grease the bearings/swivel. Change the inline filters to remove trapped dirt. Your pressure washer senses that it is overheating and turns everything off. These are just a few suggestions as to what is potentially stopping your pressure washer surface cleaner from spinning.
Release air from system: Always connect the garden hose to the power washer first. Then turn the water tap on and pull the trigger gun to release water from the system at the garden hose water pressure before starting the engine or motor. This will release all the pressure from the system and allow the pump to function.