Show more
See More
Pacbrake HP10206 vs Firestone 4193 vs Airlift 57289. You bought a RAM truck for the brute strength it exhibits over competitors in the class, especially when it comes to towing and hauling capacity. You didn’t settle for anything...
Show more
See More
Every Pacbrake exhaust brake has a 1/8" NPT port tapped into the side of the exhaust brake housing. It has a port plug threaded into it from the factory. Remove the plug and install a back pressure gauge to this port. Go for a test drive and observe the backpressure readings. My exhaust brake comes on at idle.
Show more
See More
1/8" Steel end caps Only 9 support wires 1/4" Fiber reinforced thermoplastic composite end caps Only 15 support wires Pacbrake Air springs have no equal. Use Pacbrake's heavy-duty air springs to eliminate your vehicle’s sag, sway, and bottoming out.
Show more
See More
HP625 SERIES - Our 3/4 HP Pacbrake air compressors have a 100% duty cycle (1 Hour @ 100 psi) and are offered in two pump head configurations: vertical (available in 12 and 24 VDC) & horizontal (12 VDC). Compressor Highlights Universal Applications All Pacbrake compressors have a max working pressure of 150 psi and are an oil-less design
Show more
See More
Oct 16, 2007 . '03, Quad, Dually, 4x4, HO/6-Speed, 5" Stacked, BD/AFE, Edge EZ, Stainless Boards, Pac Brake, B&W+ (fifth-wheel) hitch, Graphics by Victory Lane Graphics :$: '98, 3500XHD, "Tandem Ram", 22ft Flatbed, Tag Axle, 19,000 GVWR - '99, 3500 12' Flat/Dump/Service Truck '79 Lil Red Express-1970 MoPar "Rapid Transit System" Partial …
Show more
See More
Pacbrake exhaust brakes are designed specifically for individual engine applications to maximize performance and reliability. They are not a one size fits all compromise When the brake is deactivated, exhaust flow is unrestricted and won't interfere with power output Patented 90 degree Non-contacting Butterfly Valve is specially engineered to maximise backpressure while …
Show more
See More
Every Pacbrake exhaust brake has a 1/8" NPT port tapped into the side of the exhaust brake housing. It has a port plug threaded into it from the factory. Remove the plug and install a back pressure gauge to this port. Go for a test drive and observe the backpressure readings. My exhaust brake comes on at idle.
Show more
See More
AMP AIR SPRINGS – #1 ON THE MARKET WITH LIFETIME WARRANTYPacbrake has been in the business of building heavy-duty products for OEMs and the aftermarket for ...
Show more
See More
Every Pacbrake exhaust brake has a 1/8" NPT port tapped into the side of the exhaust brake housing. It has a port plug threaded into it from the factory. Remove the plug and install a back pressure gauge to this port. Go for a test drive and observe the backpressure readings. My exhaust brake comes on at idle.
Pacbrake's heavy-duty air springs provide added support for an overall smooth and safe ride Your truck’s suspension was designed as a compromise between capacity and comfort.
Insert both wires of the Pacbrake 'through head harness' through the grommet from the outside. NOTE: In trucks with limited access at the rear of the cylinder head, it may be easier to slide the grommet out of the head. 3 5 Installation¤
Pacbrake P-61 and P-63A engine brakes are protected by law. U.S.patents 4,655,178 / 4,898,128 / 5,036,810. Pacbrake is a registered trademark of Pacbrake Company. Other trademarks used herein are property of their respective holders.