Show more
See More
Current Sensors, Temp sensors for Arduino PIC ATMEL Propeller PICaxe PSOC ARM
Show more
See More
Helios 200 Heat Bed kit 200 x 200 mm. Price: $40.00. Azteeg X5 GT 32bit Motion Controller. Price: $110.00. SureStepr SD8825 Stepper driver.
Show more
See More
Features and Specs: Made with 4 Layer 2oz copper RoHS ( v1 2 Layer) 1, 1/2, 1/4, 1/8, 1/16 and 1/32 Microstepping Up to 2.5 Amps drive current Chip has built in logic supply Bottom mounted parts for better heat dissipation Comes with Heat sink Easy to use DIR/Step insterface Over current, Over temperature and short circuit protection
Show more
See More
Detailed Specs (running RAMPS) 32-bit LPC1768 ARM processor; 100Mhz, 512kb Flash; mini B USB - Prototype photos shows USB B; 3.3V system voltage; 10-30V power supply input range, using Vin pin or barrel jack; 1 Heated bed, 2 Hotend Mosfet drivers; SD card slot for firmware upgrades and config file; 6 End stops, with filter and pull-ups ; 3 thermistor inputs
Show more
See More
Features: Measures Bi-directional AC and DC currents. Low noise, Low loss Monolithic Hall IC. Fast and accurate analog output. High isolation from measured circuit. May be used as High-side or Low-Side sensing. 3V to 5V single supply operation. Measured circuit up to 300V AC/DC. High capacity stitched copper pads.
Show more
See More
Digital Pot stepper current control can now be achieved on plug-in drivers using the Panucatt stepper drivers on the X3 PRO. Features: Atmel ATmega 2560 with FT231x FTDI USB chip. Compatible with Marlin, Repetier, others. 3 Separate Power inputs with …
Show more
See More
Store. Panucatt Devices Azteeg X5 mini WiFi 32BIT All-in-one Controller. The X5 mini WiFi is a 32 bit ARM controller which is ideal for use with 3D printers as well as CNC machines, and the newest version also includes WiFi! This controller uses Smoothieware firmware which blends perfectly with the 120Mhz NXP LPC1769 ARM chip which enables lightning fast calculations …
Brand: Panucatt
Availability: Out of stock
Show more
See More
Features and Specs: Sturdy Black anodized Aluminum Frame High Temperature Polycarbonate panels (Impact resistant too) Smoke gray see though panels (Clear front panel) Pre-machined openings (Fan, Wires, Filament, Etc) Detachable door hinge (Left and Right hinges included) Temperature meter included (Optional Thermostatic Fan and Meter)
Show more
See More
The SureStepr SD2209 is a bi-polar stepper motor driver based on the latest TMC2209 chip from Trinamic. Runs significantly quieter and smoother compared to previous stepper divers generations. Simple to use and operate using an indexer (DIR/STEP) interface to move the stepper motors. The SD2209 is a drop-in replacement for Pololu style ...
Show more
See More
Find helpful customer reviews and review ratings for Panucatt Devices Azteeg X5 mini 32BIT All-in-one Controller V1.1 at Amazon.com. Read honest and unbiased product reviews from our …
Show more
See More
Store. Panucatt Azteeg X5 GT 32bit Motion Controller. The Azteeg X5 GT is a 32 bit ARM based Motion controller for 3D printers, CNC Machines and Laser cutters. The X5 GT runs on Smoothieware firmware and is based on Smoothieboard by Arthur Wolf. The X5 GT uses the powerful 32bit, 120Mhz NXP LPC1769 ARM chip capable of faster calculations for faster and …
Show more
See More
The above Panucatt Devices deals are at the moment the finest across the web. CouponAnnie can help you save big thanks to the 13 active deals regarding Panucatt Devices. There are now 3 promotion code, 10 deal, and 2 free delivery deal. For an average discount of 20% off, consumers will score the ultimate financial savings approximately 25% off.
specs
Show more
See More
Able to run CNCs, Laser cutters and 3D printers. Technical Specifications (running RAMPS) 32-bit LPC1768 ARM processor 100Mhz, 512kb Flash Mini USB B connector 3.3V system voltage 10-30V power supply input range, using Vin pin or barrel jack 1 Heated bed, 2 Hotend Mosfet drivers SD card slot for firmware upgrades and config file
Show more
See More
Panucatt Devices, Irvine, CA. 657 likes. Panucatt Devices is an Open Source Hardware company based in Irvine California.
Show more
See More
Digital pot stepper driver current control. 1 High Current Mosfet for Heat bed control. 1 Mosfet for Hotend control. 1 FAN Mosfet. 4 end stops and 2 thermistor inputs. Wide input high efficiency switching Power supply (5v @ 1A max). Micro SD card slot built in. High current Terminal blocks can Handle up to 20 Amps per pin.
Reviews: 1
Show more
See More
Wide input (12-24V) high efficiency switching Power supply (5v @ 1A). microSD card socket built-in. On board SMT buzzer. Fused and Zener protected +5v Vcc line. Ultra Low RDSon, High power Mosfets for minimal heat buildup. Input power selector for micro controller [USB or internal regulator]. High current capacity connectors and PCB traces.
Show more
See More
The Panucatt Azteeg X3 is a robust 3D printing controller which is powered by the Atmel ATMEGA2560 micro controller. This controller can handle most printer configurations including single extruders, dual extruders, and large heated bed models. Some of the printers that work great with the Azteeg X3 include Printrbots, the MendelMax, and Ordbot.
It is based on the Azteeg X3 controller board that's been used by many 3D printer builders. Powered by the Atmel ATMEGA2560 micro controller chip, the X3 PRO is designed with excellent high current capability and compatibility with popular firmwares like Marlin and Repetier.
This controller is very similar to the X3 controller board which is commonly used by 3D printer manufacturers. The X3 PRO is powered by the Atmel ATMEGA2560 micro controller chip and is designed with excellent high current capability. The controller is compatible with most firmwares.
The X3 PRO is powered by the Atmel ATMEGA2560 micro controller chip and is designed with excellent high current capability. The controller is compatible with most firmwares.