Please contact technical support for direct assistance. Monday – Friday. 8 am – 6 pm PST. [email protected]. Phone: 402-477-0695. While updating firmware on Body Packs and Base Stations, please disable any file syncing and computer …
Show more
See More
General Information The Radio Active Designs® UV-1G is a two-channel full-duplex UHF/VHF wireless intercom system that utilizes up to six wireless Belt Pack units per Base Station. Each Belt Pack is …
Show more
See More
Radio Active Designs Appoints Jim Bakker EMEA Sales Manager . East Rutherford, NJ (October 2019) – Radio Active Designs CTO James Stoffo has announced the appointment of Jim Bakker to the position of EMEA sales and technical support director.
Show more
See More
Radio Active Designs implements Amplitude Modulation rather than traditional Frequency Modulation. This is because our goal from the start was Spectral Efficiency. Due to the fact that we are using AM, we can pack 200 belt packs and 30 base stations in the same UHF footprint as One 4 drop FM system. That makes us 30 times more spectrally efficient.
Show more
See More
Balun Designs for Wireless - Mixers, Amplifiers and Antennas.pdf - 550.14 KB Binaural Basics.pdf - 572.66 KB Brain Waves and Biofeedback Training.pdf - 422.88 KB
Show more
See More
Radio Active Designs is dedicated to helping wireless operators manage the increasingly challenging RF environment. The company’s goal is focused; create the most spectrally efficient and reliable wireless intercom systems available.
Show more
See More
FCC ID application submitted by Radio Active Design, LLC for Wireless Intercom System-Belt Pack for FCC ID 2AA6F-UV-1GBP. Approved Frequencies, User Manuals, Photos, and Wireless Reports.
Show more
See More
2. Press the manual time setting tab on the back of the clock 15 times. 3. Put the battery back into the clock. 4. The clock will go to 4:00, 8:00, or 12:00 and stay there while waiting for the signal. 5. Immediately after your clock stops at 4:00, 8:00, or 12:00, push and hold the manual time set tab until you get to the correct time.
Show more
See More
Radio Active Designs has introduced the production community’s first ever Enhanced Narrow Band™ wireless intercom system. Enhanced Narrow Band™ offers RF channels possessing an occupied bandwidth of a mere 25 kHz with the audio characteristics one would expect from a traditional FM system. The UV-1G also utilizes the relatively unused VHF ...
Show more
See More
Radio Active Designs. March 24, 2020 ·. Join us on Wednesday, March 25 as Practical Show Tech hosts James Stoffo to discuss all things RF as they relate to the live event industry. We will cover topics including the FCC spectrum repack, fundamental concepts of RF, dealing with challenging environments (like LED walls) and much more. 4:00 PM EDT.
Show more
See More
ARRL Radio Designer is an obsolete software program for circuit modeling sold between 1994 and 2000. We were forced to discontinue it, as the new owners of the company that produced it declined to recompile it for new operating systems. While it runs fine on Windows 3.1 and 95, it should not be expected to be compatible with Windows Millenium ...
Show more
See More
Show more
See More
Radio Active Designs | 83 followers on LinkedIn. Manufacturer of Professional Wireless Intercom Systems, Radio Active Designs has introduced the production …
Show more
See More
Active filters are RC networks that include an active device, such as an operational ampli- fier (op amp). Section 16.3 shows that the products of the RC values and the corner frequency must
With the demand for cell phone and data service everywhere, as well the need for reliable communication during emergency situations, the need for a DAS solution in a coverage challenged location is fast becoming a necessity.
A microprocessor activates the receiver and processes the time signal from Fort Collins overnight. Through the radio signals, our radio controlled clocks always keep precise time. The changeover from standard time to daylight savings time, and vice versa, takes place automatically with the same precision.
Sometimes called antenna nodes, these antennas are the redistribution points of the DAS network. With the aid of the remote antennas, the RF signals are distributed to places they could not directly reach without the distributed antenna system.