2. Electrical Characteristics
Show more
See More
Using your " Command Prompt " or " Terminal ", navigate to your SD Card and type this command to generate the " rak_ap " file. cd > rak_ap Check if the rak_ap file is …
Show more
See More
# RAK7200 Quick Start Guide # Prerequisites # What do you need? Before going through each and every step in the installation guide of the RAK7200 WisNode Track Lite, …
Show more
See More
RAK2287 Quick Start Guide. Insert your RAK2287 mPCIe card into the mPCIe slot on the RAK2003 Pi HAT. Make sure the card fits snugly into the connector, it should end …
Show more
See More
Open the tool, select the desired port (default baud rate) and open it. Then start importing your settings. Configure your LoRa band and activation mode. This tutorial will be …
Show more
See More
#2. Via the Ethernet Port on the Raspberry Pi 4. You can also connect your PC with the Gateway through an Ethernet cable. By default, the IP address of the Gateway’s …
Show more
See More
Enter root mode by typing the following command: sudo -i. If you are not in root mode, enter ssh [email protected] in the terminal to login to your Gateway, the default …
Show more
See More
RAKwireless recommends a lightning arrestor to be installed on all the antenna N-Type terminals ( LoRa, LTE, Wi-Fi and GPS ). It is recommended to use a 10-AWG or better …
Show more
See More
# Quick Start Guide # Software Setup. Getting started with the WisBlock products is simple and straightforward. The first thing you need is to set up your software development …
Show more
See More
Apr 29, 2017 . Put the board in flashing mode by placing the supplied sleeve so as to bridge the pins 3V3 and BOOT. Connect the board to your computer with a USB cable. It should set up …
Show more
See More
RAKwireless is a leading IoT solutions provider that constantly commits to the production of high-quality LoRa® gateways, sensors, kits and accessories for everyone to use. ... Quick Support. …
Show more
See More
WisBlock is an amazing product built by the RAK company for IoT industry. It can build circuits like clicking blocks together to quickly realize your idea. WisBlock consists of WisBlock Base, WisBlock Core, WisBlock Sensor and WisBlock IO. 1. WisBlock Base → the block that the whole system is build on. 2. WisBlock Core → the processing unit with the micro-controller. 3. WisBlock Sensor → the blocks with variety of sensors. 4. WisBlock IO → the blocks that extend the com…
Show more
See More
Code. Connect! This affordable kit features a selection of 13 different WisBlock Interface, WisBlock Wireless, and WisBlock Sensor modules to give you a quick start for the …
Show more
See More
RAK2245 Pi Hat Edition is the largest of the RAK2245 family, however, it offers complete compatibility with the Raspberry Pi 40pin header. Thus it is a perfect solution for a DIY …
Show more
See More
Feb 21, 2019 . Quick start with RAK8212 iTracker NB-IoT/Cat M/GPRS module which come from RAKwireless, and connect to Hologram online service. Intermediate Full instructions provided …
Show more
See More
RAKwireless continues to bring easy to implement solutions to IoT developers and connect the world like never imagined before. I am ready to start a new project with RAKwireless. Do you want to learn more? Contact us Do you want to be a Value Added Reseller?
By default, the firmware is configured to operate the Raspberry Pi in Wi-Fi AP mode, which means that you should be able to find an SSID named “ RAKwireless_XXXX ” on the Wi-Fi network list, for example: Connect to this Wi-Fi SSID by using "RAKwireless" as the default password.
By default, the gateway will work in Wi-Fi AP Mode which means that you can find an SSID named like " RAKwireless_XXXX " on your PC Wi-Fi Network List. “XXXX” is the last 2 bytes of your RAK7244’s WiFi MAC address. Connect to this Wi-Fi SSID using the password provided below.
Quick start with RAK8212 iTracker NB-IoT/Cat M/GPRS module which come from RAKwireless, and connect to Hologram online service. We have seen quite a lot of projects on the RAK itracker and I definitely had a blast using this board to its full potential.
By default, the gateway will work in Wi-Fi AP Mode which means that you can find an SSID named like " RAKwireless_XXXX " on your PC Wi-Fi Network List. “XXXX” is the last 2 bytes of your RAK7244’s WiFi MAC address. Connect to this Wi-Fi SSID using the password provided below.
Set up RAK Gateway LoRa Concentrator - used to configure the frequency, which the Gateway will operate on, and the LoRaWAN Server which the Gateway will work with. Restart packet -forwarder - used to restart the LoRa packet forwarded process.
Antenna Feeder Line for RAK7249 Lightning Protection. This antenna feeder line is an NJ-NF adapter cable with a length of 1.5m. It is an RG8 coaxial cable with N-type connector as the antenna feeder.
For details about the interfaces and connectors of RAK7249 WisGate Edge Max Gateway enclosure, refer to the Datasheet. Fix the support plate on the base with three M3*6 screws. Install the motherboard with four M3*6 screws. Install the LoRa card. The motherboard supports two LoRa cards.