Rivet Nuts Use Guide

Listing Results Rivet Nuts Use Guide

About 15 results and 3 answers.

How to Install a Rivet Nut: 11 Steps - wikiHow


Drilling a Hole
Fit a ⁄8 inch (0.32 cm) drill bit into a power drill. In order to drill a clean hole through the metal, you need to start with a small drill bit to create a tiny hole. Rotate the chuck, or end of the drill, to open the jaws that clamp onto the bit. Insert a small drill bit into the end of your power drill, hold the chuck again, and squeeze the trigger to close the jaws and hold the bit in place. Make sure the drill bit is held securely by tugging at it. Use a ⁄8 inch (0.32 cm) drill bit or smaller to start. Place the bit against the metal and start drilling slowly. Bringing the drill to full speed before you set it against the metal can cause it to shoot off in another direction and potentially scratch the surface. Place the drill bit against the surface and bring the drill up to speed slowly. Thin metal sheets or softer metals such as aluminum will be easier to drill through. Bring the drill to full speed so it can push through the metal. Push the drill bit through the metal. While the drill bit is spinning, apply constant pressure by pushing against the drill with your hands. Eventually, the drill bit will penetrate the surface of the metal. Push it through the metal to create an even hole. Don’t use jerky movements or attempt to shove the drill bit through the metal or it could move out of place and scratch the surface.Tip: Slide the drill bit in and out of the hole a few times to give a smooth edge to the hole. Increase the size of the drill bit to widen the hole until the Rivet nut fits. Swap out the drill bit for one with a larger diameter and place the end of it into the hole you made with the smaller bit. Bring the drill up to speed slowly and apply pressure to it. Drive the drill bit through the hole to create a wider opening. Try sliding the Rivet nut into the hole whenever you change bits to see if it fits. Whenever it slides into place, stop increasing the size of the hole. Try to fit the Rivet nut into the hole before you widen it further.
Fitting the Rivet Nut onto the Mandrel
Connect a mandrel and nosepiece that fits your Rivet nut to the tool. On a Rivet nut tool, the mandrel is a rod that holds the Rivet nut in place when you’re securing it to the metal and the nosepiece holds the Rivet nut on the tool when you’re installing it. Slide it into the tool and screw on the nosepiece that secures it and allows you to thread your Rivet nut onto the tool. Most Rivet nut tools have several mandrels of different sizes, so choose the one that fits the Rivet nut you plan to install.Tip: If you can’t locate where you need to insert the mandrel on your tool, check the owner’s manual, or look up the make and model of your tool online. Open the handle of the Rivet nut tool. The handle of the tool needs to be loaded up so you can drive the Rivet nut into the hole and install it. Use both hands to pull the handles of the tool apart so it’s fully open and is ready to receive the Rivet nut. If you try to install the Rivet nut with the handle closed, the tool will not work. Screw the Rivet nut onto the nosepiece of the mandrel. At the end of the mandrel is a threaded nosepiece. Attach the Rivet nut by screwing it onto the end of the mandrel until it’s flush with the end of the tool. You will see the very end of the mandrel inside of the Rivet nut. Pull the end of the mandrel back and wind the adjuster. With the Rivet nut flush against the end of the tool, pull on the back end of the mandrel. It will slide back a little bit and allow you to turn the adjuster knob to tighten it. Turn the knob until it’s flush against the back edge of the tool. Tighten the knob well so the mandrel is held securely.
Securing the Rivet Nut
Insert the Rivet nut into the hole. Hold the handles of the tool and slide the Rivet nut into the hole. Press the edges of the nut so they’re even and flush against the edge of the metal you’re installing it into. Avoid installing the Rivet nut at an uneven angle or it won’t be as secure. Squeeze the handles of the tool together. Use both of your hands to press the 2 handles of the Rivet nut tool together. The tool will force the Rivet nut to expand inside of the hole, which will connect it to the metal. You won’t hear a "click" or a "pop" when the tool is finished install the Rivet nut. Bring the handles together as far as you can.Warning: Avoid forcing or jamming the handles of the tool together or you could damage the threading of the Rivet nut and make it unusable. Unscrew the mandrel to complete the installation. Unscrew the adjuster knob at the end of the tool and slide the tool off of the mandrel. Then, turn the mandrel to unscrew it from the Rivet nut attached to the metal. You can now use the Rivet nut to install screws to the metal. Use your fingers to try to wiggle the Rivet nut to make sure it’s secure.

Show more

See More

5 Tips for Rivet Nut Uses and Installation - Bay Supply

Show more

See More

The Essential Guide to Threaded Rivet Nut Inserts Online

There are different Rivet nut choices depending on the application, and each is installed differently: Wide front-side flange – This style of Rivet nut features a large load-bearing surface that both reinforces the hole and... Thick flange – This …

Show more

See More

Types of Rivets: A Guide to Rivet Types and Their Common Uses


Whatis a Rivet?In a nutshell, a Rivet is a mechanical fastener or connector with a head and tail at opposite sides. It has a head, a smooth cylindrical body, and a tail that looks more like a metallic pin. Rivets are usually made of aluminum or steel, but there are some made with other materials. These types …
How Do Rivets Work?Rivets are quite an essential tool in machine and structure construction. You can install Rivets either through drilling, punching, or placing them in a hole and deforming the tail. The most popular Rivetingprocess includes drilling a hole in parts to be Riveted. This is because it is much …
Published: Jan 05, 2022

Show more

See More

Tips To Install and Use the Rivet Nuts - bestofezine

Use in a variety of materials Rivet nuts are simple, dependable fasteners that offer strong load-bearing threads in a thin gauge material comprising castings, panels, housings, tubes, and extrusions. Rivet nuts can also be fitted in a variety of material thicknesses due to their wide grip range tolerance. Other fasteners are less practical

Show more

See More

How to Install Rivet Nuts: a Step-by-Step Guide

Feb 01, 2022 . Step 1: Using the Riveting tool, expand the existing Rivet holes. This is what it will look like after being expanded. Once you have your Rivet nut in place, the hole must be opened up before installing it with a Riveting hammer. You can do …

Show more

See More

Rivnut Uses Using Rivnuts Blind Nut Insert

RIVNUT® Design and Assembly Advantages Installs blind in sheet metal, plastics and tubular materials. Can be used as a Rivet to assemble two or more materials and as a nut for the attachment of a mating part with a screw. Installs into galvanized or prepainted materials without damaging surface finishes.

Show more

See More

How to Install a Rivet Nut: 11 Steps

Things You Should Know Use a drill bit designed for whatever material you’re installing the Rivet in to drill a pilot hole for the nut; the bit... Carefully drive the pilot hole into the surface where you’re installing the Rivet using the lowest …

Show more

See More

Rivet Hole Size Chart & How to Determine the Rivet Size

The proper diameter Rivet would be 3 x 0.060=0.180 inches. A 3/16” Rivet (0.188 inches) should be used. The metal thickness is 0.060+0.060=0.12 inches, and 1.5D is 1.5 x 0.188 inch = 0.282 inches, so the total length would have to be 0.12 + 0.282=0.402 inches for the Rivet. Rivet Size Conversion - Rivet Diameter Chart.

Show more

See More

Rivet Nuts Rivet Nuts & Threaded Inserts

The Ribbed K Rivet Nut Series Benefits: Splined Body The splined body provides increased torque-to-turn resistance over conventional non-splined inserts. Near-Flush Installation The low-profile head provides near-flush seating without special hole preparation. Wide Grip Range

Show more

See More

DIY: How to Install Rivet Nuts Without Special Tools

Rivet nuts are often used in thinner gauge materials where strong, load-bearing threads are needed to fasten pieces together or where there’s no access to the back side for a traditional hex nut. At Spyder Industries we use them in the steel tubing of our headache racks for pickup trucks so that you can bolt the adjustable bed rails (or mounts) to the bottom of the rack.

Show more

See More

Rivet Nuts Information G.L. Huyett

What materials are best for use with Rivet nuts? Rivet nuts work with a wide range of materials including carbon fiber, plastic, fiberglass, steel, and aluminum. They work best in thin walled applications where tapped holes are not feasible.

Show more

See More

Frequently Asked Questions

  • How to install RIVNUT rivet nut nutserts with tool?

    To install Rivet nuts without a tool, you will still need more than just your bare hands. You will also need a bolt that 1) has its own nut, and 2) can fit into the Rivet nut. You should also have a washer or larger bushing that can fit around the bolt fairly tight. For tools, you will need an open-end wrench as well as a pair of water pump ...

  • What is a rivnut, how does a rivet nut work?

    Rivet nuts are fundamentally an expanding nut that attaches onto a steel sheet surface for bolting purposes, where a simple hole opening is not possible because the material is too thin to hold a bolt or a screw. Ideal for punched or drilled holes, they can be installed at any stage of the production, even after finish coat is applied.

  • How to install nutserts without tool?

    You can try using a short bolt, with a star locking washer, to keep the nutsert from turning. Or a longer bolt with someone holding a nut on the back and have them let you know when it's compressed. Or borrow a tool. Look at www.mcmaster-carr.com for part number 92388A238, 5/16-18 Rivet Nut installation. Price is $203 USD.

Have feedback?

If you have any questions, please do not hesitate to ask us.