Oct 24, 2018 . I am trying to figure how to wire in my Zeeltronic 10v ignition. But my original wiring does not match the Zeel diagram. 85 RZ F1 Resto. A good starting point would be checking out the wiring diagram for the no sparks! the unit i have is a Zeeltronic rzcdi-rz4 it has 11 wires 9.
Show more
See More
The Zeeltronic PCDI-10V does not run the same cleaning cycle as the OEM PV controller, it goes OPEN - CLOSED, not OPEN - CLOSED - OPEN. This means that you don’t set the PVs the way its done in the manual... if you set the PVs like that you could cause damage to the servo motor or the cables or both.
Show more
See More
Aug 24, 2016 . Rapida guida sul montaggio completo (e corretto) della ZeeltronicQuick Guide on the Zeeltronic complete (and correct) setuphttp://www.Zeeltronic.com/page/pdc...
Show more
See More
Address: 119 Braintree St Ste 701 Boston MA 02134 . Phone: (877) 644-7592 . Email: Pre-Sales [email protected] Customer Service [email protected] Tech Support
Show more
See More
Installing the Zeeltronic programable electronic ignition on our Bultaco Drag Bike project
Show more
See More
Dec 30, 2009 . Dec 28, 2009 . The Zeeltronic is a great bit of kit IMO for the money you pay. You get good gain by just fitting it and playing with the ignition curves. As for pipes if your looking for grunt have some custom pipes made. But you need to know your port timing to get the best of of the chamber pipe. Whinging Pom,s suck c**k. bryan.
Show more
See More
Zeeltronic PCDI10T CDI for Yamaha RZ350. Programmable CDI/Ignition controller. This unit replaces the stock RZ350 CDI. Ability to program your own ignition valve curves or use any of 5 preloaded ignition curves (programming your own curve requires handheld or USB programmer, sold separately).
Show more
See More
Programmable Ignition Controller and Programmer by Zeeltronic for Yamaha RD250/350/400,R5 and DS6/7 Fully programmable ignition curve from 200-20,000 rpm in as little as 100 rpm increments 3 stage rev limiter. Stage 1 retards timing, stage 2 reduces spark, stage 3 cuts spark off completely avoiding over rev and blown motors Real time monitoring of revs and timing angle Store up ten custom ...
Show more
See More
Jan 29, 2021 . The green wire is raw unrectified and unregulated voltage from the charging system, it's used by the tachometer in the oem guage. 2. a pink wire, again this usually is a deal where it is a splice between two plugs, it's for the temp sensor which is unused in any Zeeltronic application. 3. red wire, powers the guage. 4. black wire, ground.
Show more
See More
Ignitech and Zeeltronic. Basic ignition curve setup Zeeltronic Ignitech Download 4DL manual's. 4DL manual's Go to content. 4DL manual's. Download 4DL manual's. TZR125 4DL Manual TZR125 4DL Parts TZR125 4DL Info . Back to content ...
Show more
See More
Product Manuals. For product instructions: Visit the Medtronic Manual Library website. Contact your local Medtronic representative. Call Medtronic ENT at (800) 874-5797 or (904) 296-9600. Print.
Show more
See More
The Zeeltronic PCDI-10V does not run the same cleaning cycle as the OEM PV controller, it goes OPEN - CLOSED, not OPEN - CLOSED - OPEN. This means that you don’t set the PVs the way its done in the manual... if you set the PVs like that you could cause damage to the servo motor or the cables or both.
There is a lot written on the internet about using the Zeeltronic ignition and really in the first instance for in-depth questions you should always talk to Borut, he invented it and knows it inside out, but in the meantime, hopefully this may help you set up your PVs.
User’s Manual HETRONIC Swiss AG Altgraben 23 4624 Härkingen Tel.: +41 (0)62 388 99 20 Fax.: +41 (0)62 388 99 29 2 © 2011 HETRONIC Swiss AG www.hetronic.ch Using the Radio Control is forbidden for anybody who has not read and fully understood this manual. Special attention should be to given the safety instructions herein contained.
For product instructions: 1 Visit the Medtronic Manual Library website 2 Contact your local Medtronic representative 3 Call Medtronic ENT at (800) 874-5797 or (904) 296-9600 More ...