You will need to: Get the ZC706 Prepare the SD card with the proper Linux image (from here and pay attention to the Linux/Windows setup). Insert the SD -CARD into the SD Card Interface Connector (J30) Plug the AD-FMCOMMS2-EBZ into the LPC LPC Connector (J5) Plug your HDMI display device into the ...
Show more
See More
You will need to: Get the ZC706: Insert the SD -CARD into the SD Card Interface Connector (J30) Plug the AD-FMCOMMS11-EBZ into the HPC Connector (J37) Plug your HDMI display device into the HDMI Video Connector (P1) Plug your USB mouse/keyboard into the USB 2.0 ULPI Controller, w/ Micro-B Connector (J49).
Show more
See More
ADRV9002 Zynq ZedBoard Quick Start Guide. This guide provides some quick instructions (still takes awhile to download, and set things up) on how to setup the ADRV9002NP/W1/PCBZ and ADRV9002NP/W2/PCBZ on: ZED Board The supported revision is C or higher. Instructions on how to build the Zynq Linux kernel and devicetrees from source can be found here:
Show more
See More
ZYBO Quick-Start Tutorial. Quick-start tutorial for the Digilent ZYBO Zynq-7010 FPGA board using ISE 14/PlanAhead. Part 1: Setting up a new project. Creating a new project. After starting PlanAhead, you will be greeted by the welcome screen. Select Create New …
Show more
See More
Quick-start tutorial for the Digilent ZYBO Zynq-7010 FPGA board using ISE 14/PlanAhead. Purpose of this tutorial. I created this tutorial to provide a quick start into the hardware and software design workflow with Xilinx PlanAhead when using the Digilent ZYBO (or ZedBoard) Zynq AP SoC evaluation board. It is targeted at beginners of the Xilinx software suite who do not want to or are not able to use Vivado.
Show more
See More
Part 1: The Quick Start Method Using the pre-made image. To get easily started on Vitis 2020.1, Xilinx has provided all the necessary files to create a... Extracting our files. It does not matter where this is extracted to, so we can keep it in the same directory where we... Create an Application ...
Show more
See More
AD-FMCMOTCON2-EBZ Linux on Zynq Quick Start Guide. This guide provides some quick instructions (still takes awhile to download, and set things up) on how to setup the AD-FMCMOTCON2-EBZ on either: ZED Board, Rev C or later.
Show more
See More
Jun 25, 2018 . ZCU102 Evaluation Kit Quick Start Guide Walkthrough This post walks through the Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit Quick Start Guide . It …
Show more
See More
RF DC Evaluation Tool for ZCU216 board - Quick start; RF DC Evaluation Tool for ZCU208 board - Quick Start; There is also a Xilinx Power Advantage Tool that runs on the Zynq UltraScale+ RFSoC boards. Zynq UltraScale＋ RFSoC Power Advantage Tool 2019.2 ZCU216; Zynq UltraScale＋ RFSoC Power Advantage Tool 2019.1 ZCU111
Show more
See More
ADRV9009-W/PCBZ Zynq UltraScale+ MPSoC ZCU102 Quick Start Guide. ... Build and start osc on a network enabled Linux host. Once the application is launched goto Settings → Connect and enter the IP address of the target in the popup window. Even thought this is Linux, this is a persistent file systems. ...
Show more
See More
After installing the logiREG-ZGPU-ZC702 reference design for Xilinx® ZC702 Development Kit, please use start.html file located in the installation root directory as a jump-start navigation page for exploring the reference design. If you want to quickly run the precompiled graphics demo applications on your ZC702 kit, please copy contents of the software/ready-for-download/linux_sd directory to the root …
Show more
See More
Set the jumpers: The main one is: SW11 - Big Blue Switch in the middle, which controls the Boot Mode, it needs to be set: 1: Down, 2: Down, 3: Up, 4: Up, 5: Down. Other Jumpers can be checked via looking at the picture. (click the picture to make it bigger) Turn it on. Wait ~30 seconds for the “DONE” LED to turn green.
Xilinx also provides a smaller set of Targeted Reference Designs or TRDs for Zynq UltraScale+ RFSoC it is called the RF Data Converter Evaluation Tool. There is also a Xilinx Power Advantage Tool that runs on the Zynq UltraScale+ RFSoC boards.
Connect the ADRV9002NP/W1/PCBZ or ADRV9002NP/W2/PCBZ FMC board to the FPGA carrier socket. Connect USB UART (Micro USB) to your host PC. Insert SD card into socket. Configure Zedboard for SD BOOT ( Set the Jumpers and Switches accordingly like shown on the above picture. (click on the picture to enlarge)).
An example design is a snapshot in time. What this means is that the design is done on a specific Xilinx tool release and not necessarily updated to other tool releases or the current release. The user can take these and update them on their own. For Zynq UltraScale+ RFSoC there are only example designs for the ZCU1275 and ZCU1285 boards.
The Zynq® UltraScale+™ RFSoC ZCU111 evaluation kit enables designers to jumpstart RF-Class analog designs for wireless, cable access, early-warning (EW)/radar, and other high-performance RF applications.
This RFSoC ZCU208 evaluation kit includes a combination of Arm ® Cortex ® -A53 and Cortex-R5 subsystems UltraScale+ programmable logic and the highest signal processing bandwidth in a Zynq UltraScale+ device. This combination makes the ZCU208 ES1 evaluation kit the most comprehensive RF analog-to-digital signal chain prototyping platform.
Xilinx Zynq ® UltraScale+™ RFSoC ZCU208 Evaluation Kit is an ideal RF test platform for both out of the box evaluation and cutting-edge application development. The Zynq UltraScale+ RFSoC ZU48DR integrates a 14-bit 5GSPS ADCS, eight 14-bit 10GSPS DACS, and eight Soft-Decision Forward Error Correction (SD-FEC) cores.
This combination makes the ZCU208 ES1 evaluation kit the most comprehensive RF analog-to-digital signal chain prototyping platform. This kit operates at 0°C to 45°C operating temperature range and is stored at -25°C to 60°C storage temperature range.